- Honeywell Lynx Programming
- Honeywell Lynx Manual
Download Installation and setup manual of Honeywell ADEMCO 5828 Keypad, Security System for Free or View it Online on All-Guides.com.
LYNX Touch L7000 Series Security System. 800-16084 12/13 Rev. B LYNX Touch L7000 Series – 2 – Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use with your security system. Your Honeywell security system is not designed for use with any device that may be. At the time of. Download Honeywell LYNX Touch L7000 Series Quick Installation Manual. Honeywell LYNX Touch L7000 Series. Related Manuals for Honeywell LYNX Touch L7000 Series. Security System Honeywell LYNX Touch L5210 Series User Manual 88 pages.
Brand: Honeywell
Category: Keypad , Security System
Type: Installation and setup manual
Model: Honeywell ADEMCO 5828 , Honeywell ADEMCO5828V
Pages: 4
ADEMCO 5828/5828V
INSTALLATION AND SETUP GUIDE
The 5828 and 5828V are wireless, bidirectional, fixed-word,
nonaddressable keypads that are used in conjunction with
LYNX Series control panels or VISTA Series control panels
Both keypads provide:
• Wall-mount plate allowing easy removal of the keypad
• Optional Desktop mount /AC adapter kit,
• Battery powered with 3-AA batteries
In addition to the above features, the 5828V keypad provides
• Memo/Message center
• Voice Response – system status, zone information, and
• Stored Message LED indication
NOTES:
• The 5828/5828V cannot be used as a primary keypad to
program and/or test any security system. All systems
require a hard-wired keypad to do so. Once programmed
and tested, the 5828/5828V can be used to initiate all
other keypad functions in both the VISTA and LYNX
series systems. However, you must have at least one
series control panels.
1
4
7
READY
AWAY
TEST
CODE
3
6
9
#
READY
A
C
5828V-00-002-V0
OFF
MAX
INSTANT
2
5
8
0
STAY
BYPASS
CHIME
D
B
Operation (See NOTE below)
battery, the keypads activate when any key is pressed.
When the key is pressed, the keypad sends a status request
to the control. The keypad displays and/or annunciates the
2. AC-Powered Operation: When powered by AC, the
. Any change in system
status will cause the display to automatically turn on (if
If AC power is lost, the keypad will revert to battery-powered
operation until AC power is restored and a new status
NOTE: Whether the unit is powered by battery or AC, the
5828/5828V may take up to 5 seconds to display and/or
annunciate the new status after pressing the [✱] key.
Before mounting the 5828 & 5828V permanently,
• If interfacing to a LYNX panel, try communicating
• If interfacing to a VISTA panel, perform a Go/No
Go test from the panel. Refer to the Go/No Go test
panel.
Avoid mounting locations on or near large metal objects,
since these can decrease the transmission range or block
• Secure the mounting plate to the wall, using proper sized
• Route the wires from the optional power pack through
the wire guides on the back of the keypad and into the
• Plug the AC adaptor connector into the keypad’s DC
• Position the keypad over the mounting plate and slide
down, engaging the four retaining clips on the plate with
DESKTOP MOUNTING
For full portability, the keypad may be placed in any conve-
nient, RF-suitable location and operated in its battery-
powered mode, or near an AC outlet to be powered by the
optional Power Pack/Desktop Mounting Kit, ADEMCO P/N
BATTERY INSTALLATION OR REPLACEMENT
CAUTION:Remove the AC/DC power connector from the
Honeywell Lynx Programming
keypad (if applicable), before attempting to install or replace
Separate the keypad from its mounting plate by sliding the
Open the battery compartment door to expose the batteries.
Related Products for Honeywell ADEMCO 5828
Related Manuals for Honeywell ADEMCO 5828
Honeywell Lynx Manual
Honeywell ADEMCO 5828: Frequently viewed Manuals